1	Win32s is not supported.
2	Please close computer management and try again.
3	Please close the disk administrator and try again.
4	Image for Windows
5	Select location for restore:
6	Select partition to backup:
7	Select source:
8	Select destination:
9	Please enter a file name or select a specific CD/DVD drive.
10	Overwrite existing file?
11	File not found.
12	Please remove the extension from the file name.
13	Please select a partition to backup.
14	Please select a location for restore.
15	File
16	&Finish
17	&Next >>
18	<< &Previous
19	Please insert disc %i
20	Please insert the last disc.
21	This disc is from a different set.
22	Out of memory.
23	Unable to find the selected partition.
24	There was a problem accessing the hard drive.
25	Unable to open or read data from the image file.
26	Restore would overlap existing partitions.
27	Unable to add more partitions.
28	Unable to write MBR.
29	The selected destination is not large enough\nto restore %lu MBs.
30	Error writing to disc!
31	An error has occured writing to the hard drive%s
32	An error has occured reading from the hard drive%s
33	\nIgnore all errors and continue?
34	Would you like to validate that the image is valid?
35	The file is not a valid image file.
36	WARNING: All data in (%s) on HD%i will be lost\nAre you sure you want to continue with the restore?
37	Unable to open file.
38	Insert a blank disc for volume %u
39	Unable to read data from file.
40	PC is too slow to image to CD.
41	Unable to mount file system.
42	The image stream is corrupt.
43	Unable to update entry.
44	Boot sector update failed.
45	Restored
46	Boot sector has been cleared.
47	Unable to add entry.
48	The destination has run out of space.
49	The disc is not blank.  Erase it?
50	Error on write or disk full.
51	Extended
52	Image has successfully completed your request.
53	Accessing CD...
54	Closing CD...
55	Imaging in progress...
56	Restoring Image...
57	Unable to Create File.
58	The CD device chosen is read-only!
59	Validating Image...
60	Erasing disc...
61	Process was canceled by user.
62	The process failed.
63	The process completed successfully.
64	&Close
65	Please Wait...
66	Image is now processing the following:\n\n
67	STATUS: FAILED!\nImage was unable to process your request.\n\nFAILED FAILED FAILED FAILED
68	STATUS: CANCELED!\nImage was canceled by the user.\n\nCANCELED CANCELED CANCELED CANCELED
69	Operation: %s\nSource: %s %s\nDestination: %s %s
70	Backup
71	Restore
72	You must enter a name.
73	none
74	Unable to obtain a lock on drive %c:%s
75	In order to create a clean image from within\nWindows the volume should be locked.\n\nAre you sure you want to continue without a lock?
76	Unable to dismount the restored volume.
77	Unable to unlock volume.
78	You are attempting to create the image file\non the same drive that is being backed up.\n\nAre you sure you want to continue?
79	The system will now be restarted!\n\nNote: Canceling the restart may cause corruption on the restored partition.
80	Because this drive is susceptible to buffer under-runs, you should be sure to close all other programs and keep this program active.
81	The evaluation period for this data has ended.  To order the full-use version visit www.terabyteunlimited.com.
82	This evaluation version only allows you to restore image files created by this evaluation version.
83	Unable to open or read data from image file.
84	Create: IMAGEW /Chx[V][B][J] [/U] /CDn|d:\filename.img[;s]\nRestore:IMAGEW /R[h][N][V][A][T][J][X] [/O|/C] /CDn[file]|d:\filename.img\nValidate: IMAGEW /V /CDn|d:\filename.img\n In the above examples the items in brackets [] are optional and the | symbol\n is read as 'OR'.\n  /Chx - Create Image: h=hard drive (0-9), x=partition id\n  /U - No Compression\n  /R - Restore Image: h=hard drive (0-9)\n  /O - Overwrite without warning (advanced).\n  /C - Clear MBR and EMBR before restore (advanced).\n  /CR - Same as /C plus restore NT Signature (advanced)\n  /CD - Get list of cd device numbers\n  /CDn - Use CD Device number n\n  N - Append N to the restore switch to not reboot (advanced)\n  V - validate the image.\n  B  - Byte for Byte validation if used with V\n  d - Drive letter -or- hard drive, partition id\n  ;s - Limit file size on creation: s=0=2GB, 1=698MB, 2=648MB\n  A - Set the restored partition active\n  X - Expand the restored partition\n  T - Write Standard MBR Code\n  J - No CD Eject
85	CD Device %u not found.
86	Byte-for-Byte
87	Byte-for-Byte comparison failed!\n\nIf you were unable to obtain a lock then this probably\nmeans some data on the partition has changed.
88	The trial period has expired.
89	The name or key is invalid.\n\n Both items must be entered exactly as recieved with your purchase.
90	Adjusting - Please wait... (may be several minutes)
91	Adjustment Error: %Xh/%u
92	Optimal
93	Unable to start PHYLock for drive %c:\nYou may need to reduce the cache size.
94	PHYLock setup error. 
95	PHYLock failed to cache all changes.  Please increase the cache size in settings.
96	PHYLock waiting ...
97	%d hour(s) 
98	%d minute(s) 
99	%d second(s) 
100	remaining.
101	 (PHYLock active)
102	 (PHYLock not active)
103	\n\nConsider using the free PHYLock add-on which\ncan be downloaded from www.terabyteunlimited.com
104	Validate
105	You have selected to backup multiple partitions to CD/DVD.\nCurrently, each partition will require its own set of discs.
106	You have selected to backup multiple partitions.\nEach partition will reside in its own set of files\nby having a hexidecimal number appended to the\nsupplied file name.
107	 (%u of %u)
108	\n\n%u of %u completed successfully.
109	Warning: You are about to use the trial version of CDBOOT.F35.\nThe CD/DVD will not boot using that version.  Please review\nthe registration email you received or see "Extracting the\nCDBOOT.F35 File" in the manual.
110	Please be sure you have extracted CDBOOT.F35 from IMAGEREG.ZIP.\nSee "Extracting the CDBOOT.F35 file" in the manual for more information.
111	The file name must be in short filename (8.3) format.
112	Do not supply a drive letter unless the "File" item is\nselected at the top of the treeview window.
113	Path must start from root (\).
114	You must run this program with administrative\nprivileges for the local machine.\n\nYou can do this by right-clicking the program\nicon and choose "run as...".
115	Access this partition via drive letter %c: by selecting\nthe "File" item located at the top of treeview window.\n\nOnce "File" is selected, either type in the file path name or\nclick the browse button.
116	Name
117	Size
118	Date/Time
119	The CD/DVD being created will not be bootable because\nthe CDBOOT.F35 file was not found in the current folder.\nBe sure the shortcut properties "start in" value is correct.
120	Insert media that contains file %s
121	Validating Disc...
122	Unable to read data from disc!
123	Disc validation failed!
124	The file size entered is not valid.
125	Warning: This system appears to contain OS RAID that has not been virtualized by the OS.  Do not use this program to backup or restore a striped volume or dynamic drive under these circumstances.
126	 (PHYLock V2 Active - Disk)
127	 (PHYLock V2 Active - RAM)
128	Unexpected Error (%u)
129	Overwrite %s?
130	Image has Expired (%u)
9001	OK
9002	Cancel
9003	&Ignore
9004	&Retry
9005	&Abort
9006	&Help
9007	&Yes
9008	&No
9009	&Continue
9010	Don't ask me again
9011	Don't tell me again
9012	Yes to &All
9013	No to A&ll